Skip to content

Brand

Offgridtec

Off-grid fittings, pre-wired

Parts that arrive finished rather than as a bag of components.

The pairing that works

The inline fuse holder comes pre-wired with 25 cm of 4 mm² cable at both ends and rated to 30 A.

That match is the point. A holder rated 30 A on thin tails is a 30 A fuse in a smaller circuit, and the tails decide what actually flows. Four square millimetres suits thirty amps, and the listing states both.

The sealing

A fully moulded rubber body with a waterproof lid, rather than two plastic halves clipped together. No IP figure is published — which is the gap — but the construction is described rather than asserted.

The adapter

A short Anderson-style lead in 9 AWG, for joining one connector standard to another without cutting anything.

What both listings omit

A voltage rating on the fuse holder, on a part sold into 12 V, 24 V and 48 V systems alike. And the fuse itself, which has to be bought to match the load.

Everything Offgridtec puts on these shelves, one page each

  • Offgridtec Anderson parallel adapter lead for solar modules

    Offgridtec 20 cm 9 AWG parallel adapter lead, Anderson 50 A both ends

    A 20 cm ready-made adapter lead in 9 AWG with 50 A Anderson connectors at both ends, for paralleling two folding solar modules.

    Current rating
    50 A Anderson connectors at both ends, third bullet
    Housing size
    Nowhere in the listing
    Colour coding
    Nowhere in the listing
    Contact material
    Nowhere in the listing
    Crimp range
    Not applicable — the lead is supplied made up in 9 AWG
    Mating cycles
    Nowhere in the listing
    Available accessories
    None — this is a finished lead, plug and play, second bullet
    Amazon reference
    B09BCY6CVY (same reference on 6 Amazon marketplaces)
    EAN
    4260737980228
    • Supplied made up, so no crimping tool and no crimping skill are required
    • A stated compatibility with folding solar modules of a named range
    • A parallel connection is not always the right one — series and parallel suit different controllers

    Best for: Two folding panels standing side by side, feeding one controller.

    ≈ £13 / €10
    Check price on Amazon
  • Offgridtec inline blade fuse holder with a black rubber body

    Offgridtec Inline blade fuse holder, 30 A, 25 cm of 4 mm² lead

    A sealed inline blade fuse holder rated to 30 A, supplied pre-wired with 25 cm of 4 mm² cable in a rubber body with a waterproof lid.

    Fuse standard
    Standard ATC and blade fuses, third bullet
    Current
    Rated to 30 A, fifth bullet
    Voltage ratings including DC
    Nowhere in the listing — 12 V and 24 V systems are named as applications, which is not a rating
    Terminals
    Pre-wired with 25 cm of 4 mm² cable at both ends, fourth bullet — no crimping needed
    Mounting
    Inline, carried by the cable; no fixing described
    Ingress rating
    A fully sealed rubber body with a waterproof lid against water, dust and dirt, second bullet; no IP figure is given
    Supplied fuses
    None — the holder is supplied alone, one piece
    Amazon reference
    B077SGP5B3 (same reference on 5 Amazon marketplaces)
    EAN
    4250983245851
    • Pre-wired in 4 mm², which suits the 30 A rating rather than undercutting it
    • A sealed rubber body rather than a plastic clip-together cover
    • No voltage rating, on a component sold into 12 V and 24 V systems

    Best for: A single circuit tapped off a battery where the run is already cabled.

    ≈ €4
    Check price on Amazon

A price quoted in the text of a PowerVerdict page dates from the day that page was written; the live figure beside each product is fetched while you read and replaces it.